Web DVR Login Error in Internet explorer 11

Dear Friends
   Do u have difficulty in login to web dvr after installing in Windows 10 or after installing it in internet explore above 10 version. Lets solve this--

1. Open Internet explorer
2. Go to settings than Internet Options
3. Go to security and select Local Internet and Make it LOW by pulling the bar down.
4. Now u Have 2 Options First Try this--
     A. Open ur web DVR Clint Address Example -192.168.2.3  in IE.
          Then u r window will show u again error that Clint is not installed, No problem Now Press F12
           Then go to Emulation
           Make Document Mode to 10
           Hurrey   Ur DVR Screen will appear.
           U Have to follow this Again And Again u will start Browser So Now----

     B. In Ur Internet explorer Open Web Clint DVR IP Address   Example -192.168.2.3
          Then u r window will show u again error that Clint is not installed, No problem..
          Now click on settings in Internet explorer and select compatiblity view setting
          Type Ur web clint IP Address and press add.

          Close u r internet explorer and open it again. Now every thing will work fine.
          

Double sided 2nd page upside down printing Problem on ( Canon MF4820d )

I found the final solution in setting.
Please follow the steps.

What ever windows You are using-

1. Go to Printer setting.
2. Now Right Click om "Canon MF4800 Series UFRII LT" Then Click Properties.
3. Now clock preferences.
4. Now go to finishing Tab and click on Advanced Setting.
5. Click on Rotate Print Data 180 degree and Select ON from bellow drop down Menu.

6.Now click ON & Finish it to come back to Step 2 Page.

7. Now go to Advanced Tab
8. Click on Printing Defaults
9. Repeat step 4 & 5.
10. Click OK & Finish It.

Dear please Remember When you are going to print select print On Both side Long Edge for Portrait & Also remember 2nd page will be printed 1st & then 1st page on Paper. So Adjust your paper header If applicable eg. Paper with header header part down & back part up in tray.

Use WiFi ADSL Modem cum router as a Wireless access point only

Use WiFi ADSL Modem Dlink 2750u cum router as a Simple Router

D Link 2730- U WiFi router as a Wireless Access Point to convert the Ethernet connection to a WiFi .

D Link 2750 U is an ADSL Wireless router with one WiFi port and four LAN ports. If you want to use this router as a WLAN access point only, the first step is disabling DHCP. For this connect the router with your PC with WiFi or Ethernet cable. Access the Modem Admin page by entering http://192.168.1.1  in browser address bar. Use the default user id “admin” and password “admin”.

Go to the LAN sub menu under Advanced Setup.  By default the DHCP server is enabled. Here you have to Disable the DHCP server. After disabling the setting save it and reboot the router.

Now you can connect Ethernet input cable to one of the four LAN ports of the router. Internet connection on this port will be bridged to other three ports as well as WiFi port. Now the device is converted as a simple WiFi access point. You may be required to enter the IP to your WLAN/Ethernet adaptor of PC/Laptop to establish connectivity (If the network shows “Limited Connectivity”) See the image. In my case the default IP address of the WiMax CPE is 192.168.0.254 which is used as default gateway.

Here I didn’t changed the default IP address of the ADSL router (192.168.1.1) just used the router as a bridge only. The same method is applicable to other routers also. Here the points to Note:

• Get the IP range of the connection which you want to extend. (Connect to network, in command prompt enter ipconfig /all. You will get the IP address and the connected default gateway).
• To avoid IP conflict, change the IP address of your WiFi router in the same range.
• Disable DHCP and NAT settings of WiFi Router
• Connect the input to one of the LAN ports.